|
An Investigation on Microstructure and Mechanical Properties of a Copper Strip Subjected to Different Routes of Accumulative Roll Bonding Process
|
10.1007/s11665-022-07145-0 |
1401 - 10 |
|
Microstructure, texture, and mechanical properties of asymmetrically cold-rolled Ni1.5FeCrCu0.5 high-entropy alloy
|
10.1016/j.jmrt.2022.10.147 |
1401 - 08 |
|
On the texture evolution of aluminum-based composites manufactured by ARB process: a review
|
10.1016/j.jmrt.2022.09.078 |
1401 - 08 |
|
Effect of annealing treatment on microstructural and mechanical properties of a hot-forged FeCrCuMn2Ni2 high-entropy alloy
|
10.1016/j.mtla.2022.101618 |
1401 - 07 |
|
Corrosion and wear resistance of coatings produced on AZ31 Mg alloy by plasma electrolytic oxidation in silicate-based K2TiF6 containing solution: Effect of waveform
|
10.1016/j.jma.2021.07.026 |
1401 - 06 |
|
Synthesis of FeCrCoNiCu high entropy alloy through mechanical alloying and spark plasma sintering processes
|
10.1016/j.matchemphys.2022.126433 |
1401 - 06 |
|
Effects of carbon and molybdenum on the nanostructural evolution and strength/ductility trade-off in Fe40Mn40Co10Cr10 high-entropy alloys
|
10.1016/j.jallcom.2022.165108 |
1401 - 05 |
|
Effects of Annealing on the Fabrication of Al-TiAl3 Nanocomposites Before and After Accumulative Roll Bonding and Evaluation of Strengthening Mechanisms
|
10.1007/s40195-021-01302-5 |
1401 - 05 |
|
Microstructural investigation of an Al-Cu lamellar nanocomposite produced by accumulative roll bonding process under the heat treatment condition: an analytical, experimental, and finite element study
|
10.1016/j.jmrt.2022.07.137 |
1401 - 05 |
|
Post-rolling annealing of a multilayered Brass/IFS/Brass composite: An evaluation of anisotropy, formability, and mechanical properties
|
10.1016/j.jmrt.2022.05.037 |
1401 - 04 |
|
Dynamic recrystallization behavior of the equiatomic FeCoCrNi high-entropy alloy during high temperature deformation
|
10.1016/j.jmrt.2022.07.055 |
1401 - 04 |
|
Enhancement of mechanical properties of a novel single phase Ni1.5FeCrCu0.5 HEA through cold rolling and subsequent annealing
|
10.1016/j.msea.2022.143360 |
1401 - 04 |
|
Data supporting the hierarchically activated deformation mechanisms to form ultra-fine grain microstructure in carbon containing FeMnCoCr twinning induced plasticity high entropy alloy
|
10.1016/j.dib.2022.108052 |
1401 - 03 |
|
Annealing texture in asymmetrically rolled Ni1.5FeCrCu0.5 high-entropy alloy
|
10.1016/j.jmrt.2022.04.126 |
1401 - 02 |
|
Grain boundary engineering in roll-bonded copper to overcome the strength-ductility dilemma
|
10.1016/j.jmrt.2022.02.032 |
1401 - 01 |
|
A study of hot compression behavior of an as-cast FeCrCuNi2Mn2 high-entropy alloy
|
10.1016/j.jallcom.2021.162732 |
1400 - 12 |
|
Investigation of hardness, wear and magnetic properties of NiCoCrFeZrx HEA prepared through mechanical alloying and spark plasma sintering
|
10.1016/j.jallcom.2021.161924 |
1400 - 11 |
|
Evaluation of TiAl3 Intermetallic Formation Mechanism and Revolution of Annealing Texture in Al/Ti Powder/Al Laminate Composite Fabricated by Cold Roll Bonding and Post-Annealing Treatment
|
20.1001.1.23830042.2022.9.2.3.5 |
1400 - 11 |
|
Abnormal texture evolution of accumulative roll bonded Al-Cu by adding alumina particles
|
10.1016/j.heliyon.2022.e08723 |
1400 - 10 |
|
Extraordinary strength-ductility in gradient amorphous structured Zr-based alloy
|
10.1016/j.jallcom.2021.161507 |
1400 - 09 |